Energic Motoculteur 228 – series 220
Engine/Moteur. 4 stroke, 8cv Bernard W 810, 8cv @ 3600 rpm., single cylinder, OHV. valves, 4 stroke, Alésage 70mm x Course 70mm, 270cm3. Air cooled. Cylinder head/Carter – aluminium with special metal cylinder lining. Cylinder head Hemispheric, with Over head valves (OHV). The piston is made up from a mixture of aluminium-silicon and copper for maximum resistance under load. Push rods are regular able, The Crankshaft is mounted on regulated roller bearings with sealing rings at each end giving full safety against the introduction of dust inside the casing. Centrifugal regulator.
Read more about Bernard engines/moteurs here.
Lubrication. By constant circulation of oil held within the sump of the engine (1.8 liters of oil). The circulation pressure being attained from crankcase pressure spraying/mist droplets of oil onto all the moving parts of the engine, including the over head valves which are under a watertight housing.
Cooling. By air circulation.
Starting. By hand turning the pulley at the front of the engine, usually with twine/cord.
Air filter/Cleaner. Filter in a bath of oil.
Gears. 6 forward and 2 reverse gears, using a second sprocket/inversion you can get 6 forward and 2 reverse.
Carburateurs. Type Zenith 24 RX or Solex 26 NH.
PTO. Rear. (prise de force). Differential blockable.
Exhaust/Silencer. Fitted to the right hand side in a frontal position (viewed from the rear looking forward), away from the driver.
Steering. By directing the handle bars, handle bars been adjustable for height.
Additional equipment. Brakes, Fully automatic wheel width regulation. potato lifter/arrache pomme dr terre, barre de coupe 1.45m, various plows (15 – 22cms) – brabant, buttior, bineuse, charrue simlpe 3 types, bi-soc plows, cultivateurs, expirpateur 5 dents, rotivator/fraise rotaive – 350/500mm, harrow/herse, wheel weights/masses, extra sprockets in the gearbox to double the gears, poulie 110mm, various towing brackets/attelages, sprayers/ pulverisateur 100liters – pipe – 1 lance, metal wheels/roues méttaliques, seed planter/semoir, winch/treuil and various variations on wheel sizes and dimensions.
The 220 series uses the same moteur- boite- pont formation that is rigid with exceptional strength, adopted from the tried and tested 409 motoculteurs.
Wheels. Pneumatic Tyre wheels 400 x 12 (hoeing/weeding) or additional cost option 500 x 15 (limited ploughing) or 650 x 16 (ploughing). Blockage independent for each wheel. With the option of “Moyeux auto-réglables” you can alter the width of the motoculteur between 50cm and 80cm, depending upon the size and dimensions of the wheels.
Brakes. Drum type, independent and regularable.
Hitch. Manual universal hitch with metal pin to attach diverse ancillary equipment, plows, hoes, etc. Paint special polymérisée.
Weight. 250+ kgs With additional wheel weights of approx. 23kgs single or (46kgs) double. Also it is possible to fill the tyre with water for extra traction and weight.
The 220 series uses the same moteur – boite – pont formation that is rigid with exceptional strength, adopted from the tried and tested 409 motoculteurs.
Transformed. Rapidly into a winch, grass cutter etc., with the correct 200 series adaptions as optional extras.
The following implements where available across the 220 series and used through out the production history;
Specialist lifters and cutters
Hitches/Attachments – sulkys
Bernard moteur W810 8cv.
Read more about the Energic motoculteur 409 here.
Read more about the Energic Motoculteiur 410 here.
Read more about the Energic motoculteur 411 here.
Read more about Energic Tracteur 519 T.M.D.Indenor engine/moteur here.
Read more about Energic Engine suppliers Ruggerini here.
Read more about Energic Engine/Moteur supplier Peugeot here.
Read more about Energic Sachs Engines/Moteurs here.
See more on Facebook page: www.facebook.com/energic.info
If you like my Facebook page then I can put more information on it./ Si vous aimez ma page Facebook, je peux mettre plus d’informations à ce sujet.